Saw blade precision correction

Scoring Saw Blade Guide: Sizes, Conical vs Split

Choose a scoring saw blade by size, kerf and conical vs split design. See XinYu Tools 120, 180 and 200 mm TCT and PCD scorers for chip-free panels.

Request a Quote

A scoring saw blade is the small blade that cuts the underside of a panel a fraction of a second before the main blade exits. On melamine, laminate, veneer, MDF and particleboard, that pre-cut is what keeps the bottom face from chipping. The published XinYu Tools Furniture Series includes TCT and PCD (Polycrystalline Diamond) scorers at 120 mm, 180 mm and 200 mm (5 in, 7 in and 8 in), all described as inverted-trapezoid (conical) scoring blades except one 200 mm TCT model whose grind is listed as On request.

This guide covers when you need a scorer, how conical and split scorers differ, how to match kerf to the main blade, and how to check alignment before you blame the teeth. It is not a substitute for How to Choose a Saw Blade for MDF and Chipboard, which decides between furniture main blades, scorers and panel-trimming blades. Diameter conversions are in the Saw Blade Size Chart.

Specifications are subject to change without notice. Other sizes, bores and tooth counts are available on request.

When a scoring blade is required

You need a scorer when the main blade would otherwise blow out the coated or veneered face on the underside of the board. Typical work:

  • Sizing laminated MDF or particleboard on a sliding table saw or a beam / panel saw
  • Cabinet sides, doors and shelves where both faces are visible
  • Any panel with a brittle surface layer that chips when the main tooth exits

You usually do not use a furniture scoring blade for:

  • Edge trimming of plywood or already-sized panels — that is the job of Panel Trimming Blades (ATB TCT, 255–320 mm, 3.2 mm kerf)
  • Solid-wood ripping along the grain — Furniture Series lists solid-wood ripping sizes on request, without a published scorer pairing
  • Aluminum profiles — use Aluminum Cutting Blades, not a wood scorer

If the top face chips but the bottom is clean, look at the main blade, feed and hold-down first, not only the scorer. If only the bottom face chips, the scorer is the first place to look.

How the scoring unit works with the main blade

On a sliding table saw or beam saw, the scoring unit sits in front of (and usually slightly below) the main blade, cutting from the underside. In general practice:

  • The scorer rotates in the opposite direction to the main blade, so it cuts into the laminate before the main tooth exits.
  • The scoring cut is shallow — just through the surface layer, not a second full-depth cut.
  • The scoring kerf is set slightly wider than the main-blade kerf, so the main teeth pass through a pre-cut slot and do not clip the already-scored edges.
  • The two blades must share the same cut line. If the scorer is offset left or right, one shoulder of the cut will still chip.

Those are setup principles, not a substitute for the machine manual. Projection, rpm and the exact kerf overlap have to be set on the saw. Max RPM for XinYu Tools scorers is On request — do not copy a speed from another brand’s 120 mm or 200 mm blade.

Feed direction and chip load still matter. A scorer that is correctly aligned but asked to take too deep a cut, or to run ahead of a dull main blade, will leave a wide, burnt groove or will still let the main blade tear the face. Adjust depth first, then kerf, then look at tooth condition.

Conical vs split scoring blades

Two scoring systems are common on industrial panel saws. They are not interchangeable without checking the scoring spindle and the way kerf is adjusted.

Type How it is built How kerf is usually adjusted In the XinYu Tools catalog
Conical (inverted trapezoid) A single blade with a tapered, inverted-trapezoid tooth or body, so the effective cutting width changes with how far the blade projects Often by changing scoring-blade height or axial position, within the kerf range the blade is designed for Published Furniture Series scorers: inverted trapezoid (conical scoring), with two listed kerf options per size group
Split (two-piece) Two thin blades on the same spindle, with shims or a spacer between them By adding or removing shims to set the gap to the main-blade kerf No split-score model is listed in the current catalog

If your saw was delivered with a conical scorer, start with the published inverted-trapezoid models below. If it was delivered with a split scorer, say so in the RFQ, and include the spindle length, bore, and the kerf you need to match. Do not assume a conical blade will drop onto a split-score arbor and adjust the same way.

XinYu Tools can discuss a custom size or style when the published row does not fit the unit. That is not the same as listing a split-score SKU that is not in the catalog.

Match scoring kerf to the main blade

Published Furniture Series main-blade kerfs and the scorers that sit in the same size family:

Main blade diameter Published main kerf Scoring family to consider Published scoring kerf options
255 mm and 300 mm (10 in / 12 in nominal) 3.2 mm 120 mm scorers 3.0 / 4.0 mm
350 mm 3.5 / 4.4 mm (confirm which value is required) Confirm in the RFQ; 120 mm or 180–200 mm depending on the kerf and the scoring unit 3.0 / 4.0 mm or 4.3 / 5.3 mm
380 mm and 400 mm (15 in / 16 in nominal) 4.4 mm 180 mm and 200 mm scorers 4.3 / 5.3 mm

The 120 mm rows are listed with two kerf options (3.0 / 4.0 mm). The 180 mm and 200 mm rows are listed with two kerf options (4.3 / 5.3 mm). Confirm which option you will run; do not treat the pair as a single width.

A practical pairing from the published numbers: a 3.2 mm main blade at 255–300 mm is intended to work with the 120 mm scorer’s kerf range, and a 4.4 mm main blade at 380–400 mm with the 180–200 mm scorer’s kerf range. The scorer should finish slightly wider than the main kerf once it is set on the machine. We do not publish a single “add X mm” clearance, because that setting belongs to the saw and to the blade’s conical range.

If you change the main blade to a different kerf, reset the scorer. A scorer left at a narrow setting under a wider main blade is a common cause of sudden bottom-face chip-out after a blade swap.

Published scoring saw blade models

Plate thickness and Max RPM: On request. Inch labels are nominal; exact conversions are 120 mm = 4.72 in, 180 mm = 7.09 in, 200 mm = 7.87 in.

Model Tip Diameter Kerf (mm) Bore (mm) Teeth Tooth grind
FN-SC-T-120-24T TCT 120 mm (5") 3.0 / 4.0 20 / 22 24 Inverted trapezoid (conical scoring)
FN-SC-D-120-24T PCD 120 mm (5") 3.0 / 4.0 20 / 22 24 Inverted trapezoid (conical scoring)
FN-SC-D-180-36T PCD 180 mm (7") 4.3 / 5.3 30 36 Inverted trapezoid (conical scoring)
FN-SC-T-200-36T TCT (as listed) 200 mm (8") 4.3 / 5.3 45 36 On request
FN-SC-D-200-36T PCD 200 mm (8") 4.3 / 5.3 50 36 Inverted trapezoid (conical scoring)

Note the bore difference on the two 200 mm blades: the listed TCT scorer uses 45 mm, the PCD scorer uses 50 mm. They are not drop-in replacements for each other. FN-SC-T-200-36T is published as TCT with tooth grind On request; confirm the grind and tip in the RFQ if your machine specification is strict.

Main blades that commonly sit behind these scorers include FN-T-300-96T, FN-T-300-80T and FN-T-300-72T (300 × 3.2 × 30 mm) and the 380–400 mm rows with a 4.4 mm kerf, in both TCT and PCD. Always pair by kerf and machine, not by diameter alone.

TCT or PCD on the scorer

The scorer sees the same abrasive surface layer as the main blade, and it runs in a smaller diameter at a shallow depth. In general practice:

  • TCT scoring blades suit mixed production, shorter runs, or shops that already service carbide in house. They are the starting point when volume is moderate and the board mix changes.
  • PCD scoring blades are usually chosen when the line runs abrasive laminated particleboard or MDF for long shifts. PCD typically lasts much longer than carbide on those surfaces, which can lower cost per cut even though the blade costs more to buy and to service. We do not publish hour counts or a price multiple — those depend on the board, the feed and how the blade is treated.
  • PCD is less forgiving of shock. Nails, metal fittings, grit in recycled boards, or a crash into a clamp can chip a diamond tip. If the raw board quality is uneven, say so in the RFQ.

A PCD-tipped version is available on request for TCT models. The catalog already lists PCD scorers at 120, 180 and 200 mm, so start with those rows when you know you want diamond.

The same TCT/PCD choice applies to the main blade. Running a new PCD scorer ahead of a worn TCT main blade, or the reverse, often shows up as one face cutting clean and the other face chipping. Replace or sharpen them as a pair when you can.

Alignment and setup checks (before you change the blade)

Most “the scoring blade is no good” complaints on a previously clean line come from setup, not from a wrong tooth grind. Work through this list before you order a different model:

  1. Same cut line. Raise a sample cut and look at both shoulders. If one side is chipped and the other is clean, the scorer is almost certainly offset from the main blade.
  2. Depth. The scorer should just cut through the coating or veneer. Too shallow leaves the coating for the main blade to blow out; too deep wastes the scorer, widens the groove, and can mark the core.
  3. Kerf width relative to the main blade. After a main-blade change, reset the conical height or the split shims so the scorer is again slightly wider than the main kerf.
  4. Flanges, bore and rotation. Confirm the bore (20 / 22 mm on 120 mm scorers; 30 mm on 180 mm; 45 or 50 mm on 200 mm) and that the blade is mounted to rotate in the scoring direction, not as a tiny main blade.
  5. Hold-down and feed. A panel that lifts at the end of the cut will chip even with a perfect scorer. Keep the pressure beam or hold-down effective through the exit.
  6. Tooth condition. A glazed or chipped scorer will burn or wander. Do not keep pushing feed to compensate.

For table-saw and sliding-table context, including when a scorer is part of the machine rather than a standalone 10 in blade, see the Table Saw Blade Guide.

Troubleshooting chip-out and tear-out

Symptom Likely cause to check first What not to do
Chip-out only on the bottom face, both shoulders Scorer too shallow, dull, or kerf now narrower than the main blade Do not immediately switch tooth counts on the main blade
Chip-out on one bottom shoulder only Lateral misalignment between scorer and main blade Do not grind the opposite side “to compensate”
Chip-out on the top face Main blade dull, wrong grind, or feed too high; not a scoring-blade diameter problem Do not open the scoring kerf to fix a top-face issue
Burned or glazed scoring groove Scorer too deep, feed too low, or teeth glazed Do not raise rpm beyond the figure confirmed for that blade
Sudden chip-out after a blade change New main kerf not rematched to the scorer; or a 45 mm vs 50 mm bore mix-up on a 200 mm scorer Do not assume any 200 mm scorer fits any 200 mm spindle
Clean cut on raw board, chipped cut on melamine Surface layer needs a scorer (or a sharper / more suitable main grind) Do not use a wood rip blade and hope the coating survives

Tooth-grind terms (ATB, TCG, inverted trapezoid) are defined in ATB vs TCG Teeth: Tooth Grind Glossary. A glossary is not a model specification; use the grind printed on the scoring-blade row.

What to include in a scoring-blade RFQ

Request a quote — or write to info@xinyutools.com — and include:

  1. Board type and surface (melamine, laminate, veneer, raw MDF or particleboard) and whether both faces are coated.
  2. Machine type: sliding table saw, beam saw, or another scoring unit, plus the machine model if you have it.
  3. Scorer type already on the machine: conical or split.
  4. Scoring-blade diameter, bore and the kerf you need to match to the main blade.
  5. Main-blade diameter, kerf, bore and tip (TCT or PCD), or the model code if it is a XinYu Tools blade.
  6. Whether you want TCT or PCD on the scorer.
  7. Any custom size the published 120 / 180 / 200 mm rows do not cover.

Application context for cabinet and furniture panels is on Panel & Solid-Wood Furniture.

FAQ

Do I always need a scoring saw blade for MDF or chipboard?

If you size laminated or veneered panels on a sliding table saw or beam saw and the bottom face is visible, yes — a scorer is the standard way to prevent underside chip-out. Raw, uncoated board may be cut with the main blade alone, at the cost of a rougher exit. Edge trimming after sizing is a different operation and uses the Panel Trimming line.

What size scoring blade do I need?

Match the scoring unit on the machine, not a generic “small blade” size. The published XinYu Tools scorers are 120 mm (5 in), 180 mm (7 in) and 200 mm (8 in). Pair 120 mm scorers with 3.2 mm kerf main blades in the 255–300 mm group, and 180–200 mm scorers with 4.4 mm kerf main blades in the 380–400 mm group, then set the scorer slightly wider on the saw. Confirm bore: 20 / 22 mm, 30 mm, 45 mm or 50 mm depending on the row.

What is the difference between a conical and a split scoring blade?

A conical (inverted-trapezoid) scorer is a single tapered blade; kerf is usually adjusted by projection or axial position. A split scorer is two thin blades with shims between them. The current Furniture Series list is conical, with two kerf options on each size group. If your machine uses a split scorer, describe the unit in the RFQ.

Should the scoring kerf be wider than the main blade?

Yes, in general practice the scorer is set slightly wider than the main-blade kerf so the main teeth do not clip the pre-cut edges. Use the published kerf options (3.0 / 4.0 mm or 4.3 / 5.3 mm) and finish the setting on the machine. We do not publish a single clearance figure.

TCT or PCD for a scoring blade?

TCT is the usual choice for mixed or moderate-volume work. PCD is usually chosen for high-volume abrasive laminates, because it typically lasts longer and can reduce cost per cut, at a higher purchase price and with less tolerance for shock. No service-life hours are published; describe your board mix and shift pattern in the RFQ.

Can I use a 200 mm TCT scorer in place of the 200 mm PCD scorer?

Not as a drop-in: FN-SC-T-200-36T is listed with a 45 mm bore, and FN-SC-D-200-36T with a 50 mm bore. Confirm the spindle and the grind (the TCT row is On request) before you treat them as alternatives.

Related pages