
Saw Blades for Aluminium Window & Door Profiles
Select saw blades for aluminium (aluminum) window and door profiles. Compare 255–600 mm TCT and PCD models, plus clamping, lubrication and RFQ tips.
Request a QuotePublished
An aluminium window profile saw blade (also searched as an aluminum window cutting blade) has to cut a thin-walled extrusion cleanly, often at a mitre, without leaving burrs on a visible frame edge or crushing a thermal-break strip. XinYu Tools Aluminum Cutting Blades are TCT and PCD (Polycrystalline Diamond) circular blades, 255–600 mm, for aluminum profiles, thermal-break aluminum windows and doors, and other non-ferrous metals.
This page is about the window-and-door cut: machine type, diameter, clamping, lubrication and burr control, with the published models underneath. For a short TCT-versus-PCD overview and the same catalog in a compact form, use How to Choose an Aluminum Cutting Saw Blade. For why a wood blade or a steel-cutting blade is the wrong tool, use Metal vs Wood Saw Blades. Application context is on Aluminum Profiles & Thermal-Break Windows/Doors.
Tooth grind and Max RPM on the aluminum rows are On request. Inch values are approximate nominal sizes. Kerf and plate thickness are separate specifications. Specifications are subject to change without notice. Other sizes, bores and tooth counts are available on request.
Start with the profile, not only the saw
Write down what is being cut before you pick a diameter.
- Standard aluminium profiles — window and door frames, mullions, sills, and similar hollow sections. Wall thickness, alloy and whether the cut face is visible all affect finish more than the machine’s colour.
- Thermal-break windows and doors — two aluminium sections joined by a polyamide or similar insulator. The blade may have to cut aluminium and the insulator in one pass. The clamp must not crush the strip, and the tooth has to stay clean through a more abrasive, mixed cut.
- Other non-ferrous work — the same product line is listed for other non-ferrous metals. If the workpiece is copper, brass or a composite with steel inserts, say so; do not assume an aluminium window blade is automatically correct.
- Not ferrous steel. Mild steel, stainless and structural bar need a different blade family (typically a cold saw or another ferrous system). XinYu Tools does not list blades for cutting ferrous steel.
Send a section drawing or a clear photo of the profile with the RFQ. A “window blade, 20 inch” enquiry leaves the wall thickness, thermal-break, bore and mitre angle unknown.
Machine types and diameter (confirm on the saw)
Industrial window and door shops typically cut profiles on a double-head mitre saw, a single-head up-cut or pull-down saw, a copy router with a cutting station, or an in-line machining centre. We do not publish a brand-by-brand compatibility list. Use the machine’s maximum blade diameter, arbor / bore, flange size and any speed limit, then choose a published row at or under that diameter.
A practical way to read the 255–600 mm range, without treating it as a machine-assignment table:
- 255–355 mm (approx. 10–14 in) — common on lighter single-head saws and smaller stations. Published TCT models in this band are AL-T-255-120T, AL-T-255-120T-B, AL-T-305-120T, AL-T-305-120T-B and AL-T-355-120T.
- 405–450 mm (approx. 16–18 in) — a frequent mid-range on production mitre saws. TCT and, from 450 mm, published PCD rows are available.
- 500–600 mm (approx. 20–24 in) — common on larger industrial double-head saws that cut deeper or wider sections in one pass. Both TCT and PCD are listed at 500, 550 and 600 mm.
Always stay inside the guard and flange capacity printed on the machine. A 600 mm blade will not mount on a saw rated to 450 mm, and a 450 mm blade may not reach through a deep profile on a larger saw. For exact inch conversions, use the Saw Blade Size Chart. 450 mm is 17.72 in (nominal 18 in), not 457.2 mm; 500 mm is 19.69 in (nominal 20 in).
Bore is mostly 25.4 mm (1 in) on the smaller TCT rows and 30 mm from 355 mm upward. AL-T-305-120T-B is the published 305 mm exception that lists both 25.4 and 30 mm. Do not assume a 30 mm blade will fit a 1 in arbor.
TCT vs PCD for window and door production
Both tip types are built for aluminium and other non-ferrous profiles; they are not wood blades with a different label.
- TCT (tungsten carbide tipped) covers the full published 255–600 mm range, including the 255 mm and 305 mm “-B” variants. It is the usual choice for mixed sections, shorter runs, or shops that already sharpen carbide.
- PCD (polycrystalline diamond) is listed at 450, 500, 550 and 600 mm. It is usually chosen when a line cuts abrasive or high-volume profiles — including thermal-break work — for long shifts. PCD typically lasts much longer than carbide on aluminium, which can lower cost per cut even though the blade costs more to buy and to service. We do not publish hour counts or a price multiple; those depend on the alloy, the insulator, lubrication and how the blade is treated.
- PCD is less forgiving of shock and of ferrous contamination. A steel screw, a steel reinforcing insert, or a crash into a clamp can chip a diamond tip. If profiles sometimes arrive with steel parts still fitted, say so in the RFQ.
- A PCD-tipped version is available on request for every TCT model. Published PCD SKUs start at 450 mm, so a 255–405 mm PCD blade should be requested as a custom, not assumed to have a model code already.
Tooth grind for all aluminum rows is On request. In general practice, non-ferrous circular blades often use a triple-chip (TCG) tooth and a lower or negative hook so the blade is less likely to climb the profile. That is a useful briefing point for an RFQ; it is not printed as the grind on the current tables. See ATB vs TCG Teeth for definitions, and confirm the grind on the quotation.
Published TCT models (255–600 mm)
| Model | Diameter | Kerf (mm) | Plate (mm) | Bore (mm) | Teeth |
|---|---|---|---|---|---|
| AL-T-255-120T | 255 mm (approx. 10") | 2.8 | 2.2 | 25.4 | 120 |
| AL-T-255-120T-B | 255 mm (approx. 10") | 3.0 | On request | 25.4 | 120 |
| AL-T-305-120T | 305 mm (approx. 12") | 3.0 | 2.4 | 25.4 | 120 |
| AL-T-305-120T-B | 305 mm (approx. 12") | 3.0 | On request | 25.4 / 30 | 120 |
| AL-T-355-120T | 355 mm (approx. 14") | 3.2 | 2.5 | 30 | 120 |
| AL-T-405-120T | 405 mm (approx. 16") | 3.8 | 3.0 | 30 | 120 |
| AL-T-450-96-100T | 450 mm (approx. 18") | 4.2 | 3.2 | 30 | 96 / 100 |
| AL-T-450-120T | 450 mm (approx. 18") | 4.4 | 3.6 | 30 | 120 |
| AL-T-500-100T | 500 mm (approx. 20") | 4.2 | 3.6 | 30 | 100 |
| AL-T-500-120T | 500 mm (approx. 20") | 4.4 | 3.6 | 30 | 120 |
| AL-T-550-140T | 550 mm (approx. 22") | 4.8 | 4.0 | 30 | 140 |
| AL-T-600-144T | 600 mm (approx. 24") | 5.0 | 4.1 | 30 | 144 |
The “-B” rows are separate models. AL-T-255-120T has a 2.8 mm kerf and a published 2.2 mm plate; AL-T-255-120T-B has a 3.0 mm kerf and plate On request. At 450 mm and 500 mm, two TCT tooth counts are listed — use the lower count if chip clearance on a heavier section is the priority, and the higher count when the cut face must be finer, then confirm on a sample.
Published PCD models (450–600 mm)
| Model | Diameter | Kerf (mm) | Plate (mm) | Bore (mm) | Teeth |
|---|---|---|---|---|---|
| AL-D-450-96T | 450 mm (approx. 18") | 4.0 | 3.2 | 30 | 96 |
| AL-D-450-120T | 450 mm (approx. 18") | 4.2 | 3.6 | 30 | 120 |
| AL-D-500-120T | 500 mm (approx. 20") | 4.4 | 3.6 | 30 | 120 |
| AL-D-550-140T | 550 mm (approx. 22") | 4.8 | 4.0 | 30 | 140 |
| AL-D-600-144T | 600 mm (approx. 24") | 5.0 | 4.1 | 30 | 144 |
PCD kerfs at 450 mm are not identical to the TCT rows of the same diameter. If you are replacing a TCT blade with PCD and want the same slot width, compare kerf — for example, AL-T-450-120T is 4.4 mm, AL-D-450-120T is 4.2 mm — and say in the RFQ whether the cut width must stay the same.
Clamping, support and thermal-break sections
Burrs and crushed frames are often a fixture problem, not a tooth-count problem.
- Support the profile on both sides of the cut, close to the blade, so the wall cannot fold as the tooth exits.
- Use pads or shaped jaws that follow the section. Flat steel jaws on a thin decorative face will mark the aluminium before the blade does.
- On thermal-break profiles, clamp each aluminium half if the machine allows it, and avoid a single jaw that loads the insulator. A crushed polyamide strip is a rejected frame, even if the cut is square.
- For mitre cuts, keep the same support at 45° as you would at 90°. A profile that is stable at square and unsupported at a mitre will burr on the long point.
- Do not let offcuts fall against the spinning blade. That is a common source of chipped tips, especially on PCD.
If you cut several section sizes on one saw, say so. A blade and a clamp setup that is perfect on a small casement profile may be unstable on a deep door mullion.
Lubrication and chip evacuation
Aluminium likes to stick to a carbide or diamond tip (built-up edge). When that happens, the tooth stops cutting and starts smearing, and the exit edge picks up a burr.
In general practice, window shops use one of these, according to what the machine is built for:
- A cutting wax or stick lubricant applied to the teeth at intervals
- A micro-mist or spray system aimed at the cut
- A flood or through-tool system on some machining centres
Follow the saw maker’s rules: some enclosed heads are designed to run with mist; others are not. We do not prescribe a brand of lubricant or a flow rate. If you already have a system, mention it in the RFQ. If you cut dry, mention that too — grind, feed and chip evacuation then have to work harder to keep the tips clean.
Clear the chips. A gullet packed with aluminium swarf will recut chips and scratch the cut face. Higher tooth counts (120T–144T on the larger rows) give a finer face but leave less room in each gullet; if you see packed chips on a heavy section, discuss a lower tooth count (for example 96T or 100T at 450–500 mm) rather than raising feed blindly.
Preventing burrs on visible frame edges
Work through this list before you change diameter or tip type:
- Use an aluminium blade, not a wood blade. An ATB wood-cutting blade can grab a profile, leave a rough face, and risk tooth breakage. See Metal vs Wood Saw Blades.
- Confirm sharpness and built-up edge. A shiny, smeared tooth needs cleaning or servicing; pushing feed will not restore the edge.
- Support the exit wall and keep the clamp tight through the end of the stroke.
- Lubricate as the machine allows, especially on gummy alloys and on thermal-break insulators that smear.
- Match tooth count to the section. Thin, visible faces usually prefer the higher published counts (120T, 140T, 144T). Heavier sections may need the 96T / 100T options at 450–500 mm for chip clearance.
- Stay inside a confirmed speed. Max RPM is On request for every aluminum row. Do not copy a speed from a wood blade or from another brand’s 500 mm disc.
- Check the kerf and plate if you are replacing a blade in a tight slot or a guided unit. Plate thickness is published on most aluminum rows; it is On request on the two “-B” TCT models.
A small, even burr that comes off with a deburring tool may be acceptable on a hidden mullion and unacceptable on a visible sash edge. Say which faces are visible when you enquire.
RFQ checklist for aluminium window and door blades
Request a quote — or write to info@xinyutools.com — and include:
- Profile type: standard aluminium, thermal-break window/door, or another non-ferrous section. Attach a drawing or photo.
- Wall thickness and the largest section you will cut, plus whether the cut is 90°, 45°, or both.
- Machine type and model (double-head mitre saw, single-head saw, machining centre, or other), maximum blade diameter, and arbor / bore.
- Preferred tip: TCT or PCD, and whether a listed model or a custom size is required.
- Diameter, kerf, bore and tooth count if you are matching an existing blade.
- Lubrication: wax, mist, flood, or dry.
- Finish requirement: visible frame edge, hidden cut, or both; burr limit if you have one.
- Quantity and whether you need a spare blade so one can stay in production while the other is serviced.
Related processing-line context, if the blade is for a larger extrusion line rather than a window shop, is on Aluminum Processing Lines. OEM and private label enquiries should include the same technical points, plus artwork or brand-marking requirements.
FAQ
What size saw blade is used for aluminium window and door profiles?
Use the maximum diameter and bore printed on the machine, then choose a published model at or under that diameter. XinYu Tools lists aluminum blades from 255 mm to 600 mm (approx. 10–24 in). Larger industrial double-head saws often run 450–600 mm blades; lighter single-head saws more often run 255–355 mm. Confirm the millimetre diameter — 450 mm is not the same as 18 in exactly (457.2 mm).
Do I need a special blade for thermal-break profiles?
You need an aluminium / non-ferrous circular blade and a clamp setup that does not crush the insulator. Thermal-break work is a stated application for this product line. It is a more mixed, often more abrasive cut than a hollow aluminium-only section, which is why some high-volume shops specify PCD on 450–600 mm saws. Describe the strip material and whether steel inserts are ever present.
Is a TCG grind required?
Triple-chip (TCG) with a lower or negative hook is common industry practice for aluminium, but tooth grind on the current XinYu Tools aluminum tables is On request. State TCG in the RFQ if that is what the machine or the finish requires, and we will confirm it on the quotation. Do not read a grind off a wood-blade glossary and assume it is already on the aluminum row.
Why is PCD only listed from 450 mm?
Those are the published PCD diameters: 450, 500, 550 and 600 mm. A PCD-tipped version is available on request for TCT models, including the smaller 255–405 mm rows. Ask for it in the RFQ rather than expecting a listed AL-D code below 450 mm.
Can I cut aluminium with a wood-cutting circular saw blade?
It is not recommended. Wood blades (usually ATB, often with a higher hook) are designed to cut timber and wood-based panels. On aluminium they tend to grab, smear and leave burrs, and they risk damaging the teeth. Use the Aluminum Cutting line, and keep furniture or panel-trimming blades on wood.
Will these blades cut steel window reinforcements?
No. This line is for aluminium profiles and other non-ferrous metals. Ferrous steel needs a different blade and usually a different machine. If a profile includes a steel reinforcing insert, say so before a TCT or PCD aluminium blade is quoted.